Brand:
HIDEAItem no.:
SMT-12150-5C-ADimming Mode:
DMX DimmingWorking Mode:
Constnat Voltage LED DriverInput Voltage:
100-277VacOutput Power(Watt):
150WOutput Voltage:
12/24VdcShape & Size:
Standard SizeSize:
277x78x25MMWeight:
1000gCertification:
UL/CULWarranty:
7 Years
This DMX led driver 150w 12v has a maximum load
of 150 watts, no minimum power load; dimming works
equally well whether powering Maxtar single color or
multi-color LED tape lighting. The sealed driver allows
for indoor or outdoor use.
Specification
Model | SMT-12150-XC-A | SMT-24150-XC-A | ||
X=1 , 2, 3, 4, 5 for DIM (DW); CCT(TW); RGB; RGBW; RGBW+CCT (RGBCW) | ||||
DC Voltage | 12V | 24V | ||
Voltage Tolerance | ±0.5V | |||
Voltage Regulation | ±0.5% | |||
Rated current | CH1+CH2+CH3+CH4+CH5=12.5A | CH1+CH2+CH3+CH4+CH5=6.25A | ||
Rated power | 150W | |||
Load Regulation | ±2% | |||
Input | Voltage Range | 100-277VAC | ||
Frequency Range | 47-63Hz | |||
PowerFactor(Typ.)@ full load | PF≥0.97@230VAC | |||
THD(Typ.)@ full load | ≤10% | |||
Efficiency(Typ.)@full load |
91%@230VAC | 92.5%@230VAC | ||
AC Current(Max.) | 1.85A | 1.85A | ||
Inrush Current(Typ.) | 88A (Twidth 120us measured at 50% I peak, COLD START, 230VAC) | |||
Leakage current | <0.50mA | |||
Protection | Short Circuit | Hiccup mode ,recovers automatically after fault condition is removed | ||
Over Loading | ≤120% Hiccup mode ,recovers automatically after fault condition is removed | |||
Over temperature | 100℃±10℃ shut down o/p voltage, automatically recover after cooling. | |||
Environment | Working TEMP. | -40~+60℃ (see below derating curve) | ||
Working Humidity | 20~95%RH, non-condensing | |||
Storage TEMP. Humidity | -40~+80℃,10~95%RH | |||
TEMP .coefficient | ±0.03%/℃(0~50℃) | |||
Vibration | 10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes | |||
Safety&EMC | Safety standards | EN61347-1 EN61347-2-13 (EU) & UL8750 UL1310 (US) | ||
Withstand voltage | I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC (EU) & I/P-O/P:1.5KVAC(US) | |||
Isolation resistance | I/P-O/P:100MΩ/500VDC/25℃/70%RH | |||
EMC EMISSION | EN55015 EN61000-3-2 ,3-3 (EU) & FCC Part 15 B (US) (≥60% loading) | |||
EMC Immunity | EN61000-4-2,3,4,5,6,11, EN61547 | |||
Others | Net Weight | 0.75KG | ||
Dimension | 277x78x25mm (LxWxH) | |||
packing | 10PCS/CTN | |||
Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. | |||
2. Tolerance: includes set up tolerance, line regulation and load regulation . | ||||
3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. |
Compatible Light Type
Cuttable design allows users to adjust the length of Bosco light strip however like, no need for any other devices,simply stick the strip lights on clean, dry surface. start to enjoy strip lighting, 100ft led strips are long enough to reach around your entire room and light the whole place up after connect with DMX led driver 150w 12v.
Related Products
Mode:SMT-012-150VDHV2
Dimming Mode : 0-10V Dimming
Output Power : 150W
intput voltage:100-277VAC
Size:260*105*45MM (L*W*H)
The led power supply 12v 150w constant voltage driver has 4 entry points to screw terminals for easy wire access and is encased in a durable, vented aluminum enclosure.
※Input terminal with 3P; Live Wire(L) , Neutral Wire (N) . Note: vacant for middle terminal
※Output terminals with 6P; LED SEC positive (LED+), LED negative (LED-). Connected to LED light; Common anode design
2P for DIM (DW) dimming;
※Please make sure you connect these correctly ,otherwise your product will not work correctly and could be damaged.
Note: there is external antenna at output side. Don't disassemble!
■ DMX512 address setting Operation
※The default address for the DMX driver is 001.
※Address settings device:
※Address settings:
① RDM setting address:
Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual.
② NFC setting address:
The DMX address can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver.
■ Adjust output voltage Operation
※Adjust output voltage slightly for DMX512 driver
1) The driver output voltage can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver.
2) Voltage range: level 1~10, each level is 0.2V. The default output voltage level is 5. Such as SMT-24030-XC-P, default is level 5 corresponding to 24V. By adjusting output voltage slightly, you could get 23.2v to 25V freely.
■ See figure below
Simple operation about DMX512 address reset and adjusting output voltage slighting by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW)